Under load, every soil, except solid rock, settles. Settlement generally occurs for two reasons: compaction of the soil, i.e. a reduction in its volume due to the expulsion of air or water from its pores, and lateral displacement of the soil along the edges of the foundation due to the sliding of solid soil particles.
Soil settlement due to compaction consists of elastic and plastic deformations caused by the loading of the foundation, in which the soil partially returns to its original state upon unloading.
Settlement due to lateral squeezing of the soil consists only of plastic deformations, in which the soil does not return to its original state upon unloading. It most often occurs with shallow foundations built at a small depth below ground surface. Lateral squeezing of the soil also occurs in very wet soil with a small angle of internal friction.
Since the allowable soil load is taken in the zone of elastoplastic deformation, settlement is calculated solely on the basis of the reduction in soil porosity under load, while settlements due to lateral squeezing of the soil, which are assumed to be negligible, are disregarded.
Settlement due to compaction depends on the permeability of the soil, since it takes place at the expense of the pores, which in natural soil are always more or less filled with water. Therefore, soil settlement under load is in fact a hydrodynamic phenomenon, because the settlement process depends on the rate at which water is expelled from the pores, in which soil permeability plays the greatest role.
Non-cohesive soils such as gravel and sand have large pores, which is why their permeability is high and pore water is quickly expelled under foundation load. Therefore, in non-cohesive soil, settlement under foundation load occurs quickly, usually even during construction or shortly thereafter. For this reason, settlement of foundations in non-cohesive soil is rarely calculated.
Cohesive soils have small pores, their permeability is low, and the expulsion of water from the pores under the action of foundation loads can last a very long time, in some fine-grained clays for decades. In addition, since the total porosity of cohesive soil is considerably greater than that of non-cohesive soil, settlement of cohesive soil is much greater.
In cohesive soil, whose pores are partly filled with air and partly with water, settlement first occurs due to compression of the air in the pores while the water content remains constant, and then settlement due to the expulsion of water from the pores. Under static loading of the soil due to the action of the weight and the service load of the foundation, both of these types of settlement occur, but the time process of settlement is different.
There are also other causes that induce soil settlement, such as a permanent lowering of the groundwater level, chemical changes in soil composition, and other disturbances in the soil.
Settlement analysis consists of a preliminary settlement calculation, which is based on laboratory testing of soil samples, and settlement observations, which are carried out during construction of the structure and for a certain time afterward.
Settlement calculation under concentric foundation loading
Let us consider a footing resting on soil consisting of several different layers, for example a sand layer H0, i.e. H1 below the footing, a layer of clayey soil with thickness H2, a layer of fine-grained clay with thickness H3, beneath which lies compacted gravel of greater layer thickness, with groundwater level NPV (fig. 1a).
For the settlement calculation, it is necessary to plot the stress diagram due to the self-weight of the soil (left diagram in Fig. 1b) and the stress diagram due to the action of the additional load from the foundation (right diagram in Fig. 1b). The stress diagram due to the self-weight of the soil is obtained from the layer thicknesses Σ_H_ and their unit weights γ. If the unit weight of sand is γ1, sand under water γ’1, clayey soil under water γ’2, clay under water γ’3, then the compressive stresses in the soil due to the self-weight of the soil will be (Fig. 1)
γ1 · H’; γ’1 · H’’; γ’2 · H2; γ’3 · H3;
The stress diagram caused by the load is obtained by calculation using one of the known methods, for example by Steinbrenner or Newmark, for different depths below the foundation.
If we denote the foundation load by P, its area in contact with the soil by A, and the unit weight of the soil at the foundation depth t below the ground surface by γ1, the specific load of the foundation is P/A while the self-weight of the soil at the same depth is γ1t. In order to obtain the additional soil load due to the foundation load, the pressure of the soil self-weight γ1t must be subtracted from the foundation load P/A, so that the additional soil load amounts to
p0 = P/A – γ1t.
At the same depth t, the stress γ1t due to the soil’s own weight also acts, so that at this depth the total stress (P/A – γ1t) + γ1t, acts, with soil consolidation under the stress γ1t completed before the construction of the structure.

Fig. 1. Settlement calculation for concentric loading of a foundation
However, if one part of the foundation above the footing is backfilled with soil (fig. 1c), the load of the fill soil 2_Q_ must be taken into account, so that in that case the additional load amounts to
_P+2_Q/A – γ1t.
For a strip footing, A = b x 1,0 m on 1 m’ of the foundation.
Settlement calculations are carried out for all layers of compressible soil down to the depth of influence of the foundation load. Formerly, the limit of the influence of the load of a structure was considered to be the depth down to which stresses of an intensity ≥ 10% p0 prevail. Today it is accepted that this limit lies at the depth where the stress from the additional load pz is equal to 20% of the stress from the soil’s own weight: pz = 0,2 ·γ_Σ_H. Below this depth no settlement is calculated. According to another rule, settlement calculations are recommended for layers down to a depth of 2_b_ to 3_b_, where b is the width of the foundation. If a gravel layer is found at the bottom, as in fig. 1a, it is not taken into account in the settlement calculation, because its settlement under foundation load is negligible and occurs during construction.
At a depth z below the footing there is a compressive stress pg due to the self-weight of the soil (Fig. 1b), with the effect of buoyancy also taken into account. To this initial compressive stress is added the pressure pz due to the action of the structure load at the same depth. Therefore, at any point M at a depth z below the footing, the total compressive stress pn = pg + pz prevails.
Under the action of the additional load, the soil settles and deforms laterally. If lateral deformations are neglected, since they are relatively small, because the allowable soil stress is in the zone of elastoplastic deformation, it may be assumed that the settlement calculation is performed on the basis of the compressibility test in the oedometer, with an undisturbed sample taken in the area of the observed point in the soil, by means of which the soil compressibility modulus Ms is determined.
From Hooke’s law we have
Δ_s_ = pz/Ms,
where Δ_s_ is the specific settlement, per unit of layer thickness, pz the stress at depth z in the soil due to the additional load.
If we assume a sufficiently small layer thickness dz, so that pz and Ms can be taken as constant, the elemental settlement will be
Δ_s dz_ = pz/Ms dz.
The total settlement of a layer of thickness H will be

If pZ and MS are constant for a layer of thickness H, then
s = pz/Ms · H.
In fact, pz and Ms are not constant for a layer of thickness H1, but their average value at point M is adopted.
The soil compressibility modulus Ms is determined in the laboratory separately for each layer. For normally consolidated soil, the modulus Ms is determined from the primary compression diagram, where the total load is σ2 = pg + pz; σ1 = pg = Σ_γt,_ the additional load Δ_σ_ = σ2 – σ1 = (pg + pz) – pg, and the corresponding values of relative compression are Δ_h2_/h and Δ_h1_/h, so it is

However, if it is overconsolidated clay, the compressibility modulus is determined from the secondary compression diagram. From the example in fig. 2 we have for:


Fig. 2. Determination of the soil compressibility modulus based on a relative compression diagram
From the foregoing it follows that the settlement of overconsolidated clay will be much smaller than the settlement of normally consolidated soil.
Influence of foundation rigidity on settlement
Although in practice there are no perfectly elastic foundations, in which the settlement of one point would be independent of the settlement of a neighboring point, for settlement calculations a distinction is made between elastic and rigid foundations.
Elastic foundations, by which stone fill and embankments are meant, cause different settlements at individual points under uniform loading. For this reason, in such foundations the settlement calculation is not carried out for the entire loaded area, but for individual points of it: the corner points A, B, C and D, the midpoint of the sides E, F, H and J, and the center point G of the rectangular area (Fig. 3). Under uniform loading, the settlement of points B, C and D is the same as that of point A, the settlement of point H is the same as that of point E, and point J is the same as point F for soil of the same composition.

Fig. 3. Calculation of settlement of individual points of the loaded area
To calculate the settlement beneath any point G of a loaded area, the rectangle ABCD is divided into four smaller rectangles, and the settlement at G is obtained as the sum of the settlements caused by each of the divided rectangles.
Rigid foundations do not settle in the same way as flexible ones, since settlement of individual points is not possible in their case. Therefore, the settlement of rigid foundations is calculated as a whole, with the mean settlement value being determined differently according to the degree of rigidity, since the distribution of pressure at the base of the foundation depends on the rigidity of the foundation.
For rigid foundations in the shape of a square or a smaller rectangle, where a < 2_b_, the settlement sG of the midpoint G is calculated and the overall foundation settlement s = 3/4 sG is adopted. For rigid foundations in the shape of an elongated rectangle or strip, the settlement is calculated at the end point E, the midpoint G, and the point M halfway between them, along the longer axis of the footing, and the average value is adopted.
Van Hamme believes that a more accurate settlement calculation is that of the “characteristic point P”, which lies at a distance from the central axes

from the middle axes. According to Van Hamme, the settlement of certain specific points of the foundation is independent of the manner in which stresses are distributed at the foundation base. For these points, settlement can be calculated under the assumption that the stress distribution at the foundation base is uniform. For a rigid footing loaded with a uniform load, for which the stress distribution at the foundation base is non-uniform and increases toward the edges of the footing, the settlement of the footing is nevertheless equal to the settlement of the characteristic point P. The stresses at a depth z below the characteristic point P of a rectangular area of length a and width b, loaded with a uniform load p0, can be calculated using the table 1 prepared by Jelinek.
The stress σzP at depth z below the characteristic point P is σzP = (σz/p0)·p0, where p0 is the additional soil load.

Table 1. Values σz/p for stresses below the characteristic point P depending on the ratio of depth z to width b and on the ratio of length a to width b of the footing
Settlement calculation on the basis of changes in the soil porosity coefficient
If we denote by e0 the porosity coefficient of the undisturbed sample taken from the soil layer, and by ei the porosity coefficient of the same sample after completion of consolidation in the oedometer under load σ1 (fig. 4a), the reduction in the initial soil volume under the action of load Δ_σ_ corresponds to the reduction in porosity, i.e. to the soil porosity coefficient
Δ_e_ = e0 – e1

Fig. 4. Settlement calculation based on the change in the soil void ratio
The initial volume of the soil sample is

Specific settlement Δ_s_, i.e. settlement per unit volume of soil 1+e0 is
Δ_s_ =(e0–e1) / (1+e0)
The settlement of an elementary layer of thickness dz is, according to fig. 4b
Δ_s_ dz=(e0–e1) / (1+e0) dz
The settlement of a layer of thickness H will be

If we let p be the stress at depth z due to the self-weight of the soil, corresponding to the load σ0 in the oedometer, Δp the stress from the additional soil load due to the structure, corresponding to the load increment Δ_σ_ in the oedometer, and p1 the total stress under the action of the self-weight of the soil and the additional load corresponding to the total load σ1 in the oedometer, the foregoing expression can be written in the form

If we denote by A the area of the stress diagram from the additional soil load, A = Δ_pH_ (shaded area in Fig. 4b), where Δ_p_ is the stress from the additional load at the middle of the layer
a=Δ_e_/Δ_p_, the ratio of the difference in the porosity coefficient to the corresponding stress from the additional load Vc = (1+e0)/a, may be written

that is, s = A/Vc [cm]
If the soil consists of several layers, settlements s are calculated for each layer; the sum of the settlements of the individual layers gives the total settlement Σ_s_.